AI Field Manual
FM-AD-04 · Guide

Architecture & Design  ·  Advanced

Cross-check specifications for coordination conflicts

The project manual is 900 pages from four authors: the architect's sections, the engineers' sections, a hardware consultant, and a set of sections carried over from the last project. Section 07 92 00 calls for one sealant at window perimeters; Section 08 80 00 calls for another. Three sections refer to a section that was deleted in the last revision. Nobody reads 900 pages in one sitting looking for those. This guide finds them, and leaves you to decide which ones matter.

Status
Published
Reading time
About 13 minutes
You'll need
The specification sections (text, not scans), the project manual's table of contents or section index, and an AI tool approved for project documents
Last reviewed
November 2026
Before you start

What AI is for here, and what it isn't

Specification coordination problems are mostly consistency problems. The same product or condition is described in two sections that disagree. A reference standard is cited in two different editions. A section points to another section that has been renamed or removed. Each one is small, and each can turn into an RFI, a change order or a failure in the field.

AI is well suited to the search. It can read many sections and compare them for overlaps, extract every cross-reference and check it against the section index, and list every reference standard with its edition. That's work a person does badly at the end of a long day and AI does consistently.

It doesn't understand design intent, and many "conflicts" aren't conflicts. Two sealants may be specified on purpose for two different joints. A different standard edition may be required by the jurisdiction. The AI finds candidates. You decide which are real, and how to resolve them, with the authors of the sections involved.

Step 1

Prepare the sections and the index

Export the sections as text, with section numbers and article/paragraph numbering intact. Get the current section index: the list of sections actually in this project manual, with their numbers and titles. Most projects use MasterFormat numbering (six digits, such as 08 71 00), which makes cross-references easy to check mechanically.

Then group the sections into sets that are likely to overlap:

  • By system: openings (Division 08) with joint sealants (07 92 00) and fire-rated assemblies.
  • By interface: where one trade's work meets another's, such as roofing and flashing, or ceilings and mechanical diffusers.
  • By author: where the architect's sections meet consultants' sections.
Step 2

Check cross-references mechanically

Start with the part that has a right answer. Every reference to another section either matches the index or it doesn't, and every standard is cited with an edition or it isn't. Run this on each batch of sections, and keep the index the same for every batch.

The cross-reference prompt
Extract every reference to another specification section from the
text below, and check each against the section index.

SECTION INDEX (sections in this project manual): [paste]
SECTIONS: [paste, with section numbers]

FOR EACH REFERENCE: the referring section and paragraph, the section
number and title as written, and a status:
- OK: number and title match the index
- TITLE MISMATCH: number exists, title differs
- NOT IN INDEX: number not in this project manual
- AMBIGUOUS: reference by title only, or "Division X" generally

Then list every reference standard cited (ASTM, ANSI, NFPA, UL, etc.)
with designation and edition year as written, and the sections citing
it. Flag any standard cited with different editions in different
sections.

This part is close to mechanical, and the results are easy to verify: look up the number in the index.

Step 3

Compare overlapping requirements

This part needs judgment, so the prompt asks for candidates, not conclusions. Give it one related set at a time, such as the openings sections with joint sealants, rather than the whole project manual.

The coordination conflict prompt
Compare these specification sections for coordination conflicts. You
are finding candidates for a specifier to review, not resolving them.

SECTIONS: [paste a related set, with section numbers]

LIST:
1. SAME ITEM, DIFFERENT REQUIREMENT: where two sections specify the
   same product, material or condition differently (product type,
   performance, finish, warranty, testing). Quote both, with
   paragraph numbers.
2. GAPS: work that one section says is "specified elsewhere" but that
   no supplied section specifies.
3. DUPLICATION: the same work specified in two sections (risk of
   double pricing or two different installers).
4. SUBMITTALS AND QUALITY: inconsistent submittal, mock-up, testing
   or warranty requirements for the same item.

For each candidate: CONFIDENCE HIGH (clearly the same item) or LOW
(might be intentionally different), with the reason.

Ask for confidence levels every time. A list that treats every difference as a conflict wastes the reviewer's time and teaches them to ignore it.

Step 4

Review with the authors and resolve

Go through the candidates with whoever owns each section: you, the engineers or the consultants. For each one, decide whether it's real, which requirement governs, and what changes. Record the decision.

Reference standard editions need the same care. Don't default to the newest edition or to your firm's master. Check the edition referenced by the adopted code (building codes list referenced standards with editions, in the IBC's case in Chapter 35), any edition required by the contract or the owner, and whether the product or assembly in question is actually covered by that edition.

Then make the changes in the specifications, not in a memo that sits beside them. If the project is already bidding, coordination fixes go out by addendum. If it's under construction, they go through the change procedures in the contract.

Step 5

Worked example: the fit-out project manual

Fictional example; the section numbers follow MasterFormat, and the conflicts are invented. A specifier checks 46 sections of a project manual before it goes out to bid.

The cross-reference check finds 312 references. Most are OK. Four are not:

  • NOT IN INDEX (3): three sections still refer to "Section 01 60 00, Product Requirements". That section was merged into another Division 01 section during this revision. The references are updated.
  • TITLE MISMATCH (1): a reference to "Section 09 21 16, Gypsum Board Shaft-Wall Assemblies". Section 09 21 16 is in the index, but titled "Gypsum Board Assemblies": shaft walls were folded into it during this revision. The reference is corrected to the current title.

The standards list shows one gypsum board standard cited with two different edition years in two sections. The specifier doesn't simply pick the firm master's edition. She checks which edition the adopted building code references for this jurisdiction, whether the contract or owner requirements name one, and whether either section has a project-specific reason for its edition. The code-referenced edition governs here, and both sections are aligned to it.

The conflict comparison returns nine candidates. The specifier and the architect review them:

  • Real (4): the window perimeter sealant is specified as one type in Section 07 92 00, Joint Sealants, and as a different type in Section 08 80 00, Glazing. Two warranty periods disagree for the same storefront. Two other items are similar.
  • Intentional (3): different sealants at interior and exterior joints. LOW confidence, and correctly so.
  • Duplication (2): both the door hardware section and the access control section in Division 28 include electric strikes. That would have been priced twice. Resolved by assigning them to Division 28 and referencing them from 08 71 00.

All fixes go into the specifications before bid, so none of them becomes an RFI.

Step 6

Record the review

Specification coordination log
[Project] — Specification coordination review, [issue/revision], [date]
Reviewer: [name]     Sections reviewed: [n]     Index version: [date]

CROSS-REFERENCES
Referring section ¶ | Reference as written | Status | Fix

REFERENCE STANDARDS
Standard | Editions cited | Sections | Resolution

CONFLICTS
# | Sections and ¶ (both quoted) | Real / Intentional / Duplication |
  Decision | Decided by | Fixed in revision/addendum

AI assistance: candidate list generated with [tool]; every item
reviewed by [name] with section authors

What stays with you: which conflicts are real, and how they're resolved.

Esc

Saved in this browser

Reading list

Contents

Reference

Keyboard shortcuts

/ or Ctrl K
Search the manual
↑ ↓
Move through search results and index entries
Enter
Open the selected result
← →
Switch discipline tabs; previous / next entry in a workflow card
Esc
Close any dialog
?
Show this list